Ordered one to see how it worked. Saw and heard lots of good things about it. First print I did, the first layer texture was smooth as glass, and I love it. Can’t wait to see how it holds up against the test of time.
This nozzle was exactly what I’ve been looking for. Got it for my SV08, and the quality of my prints got better. Sure, new nozzles work well at least the first couple times, but what about long term? Been using it since I received it, and it’s holding up stupendously. Would definitely recommend picking one up.
Not only is the stitching clean and nicely done, it’s a hat that fits great! Best part? It is adjustable if you need a tighter or looser fit.
This is a great kit and very fast shipping. Thank You West3D.
I've really enjoyed building the kit, but it has some minor issues due to missing or incompatible parts.
1. A few M3 screws are required to be socket head for the door latch mechanism, but the kit only includes button head.
2. The included steering servo includes 5 different arms, but none of them fit without cutting half of the arm off. Maybe this is typical, but I felt dirty doing it.
3. The optional battery uses a male XT60 connector, but the ESC uses a male Tamiya connector. Nothing is included in the kit to fit them together and you will need to buy an adapter or crimps to connect them.
4. The optional components don't include a battery charger, so if you're not an RC person (like me) you'll also need a LiPo battery charger.
This is the most sticky print bed I’ve ever worked on. I love it. The bottom of the print job comes off baby butt smooth. The only mistake I did is I didn’t get it double-sided.
I couldn't be happier with my order. It was shipped extremely fast and it's a high quality product.
I Got it thinking it was a build plate, but it is definitely a sticker. If I had known this, I wouldn't have purchased it. But guess it's on me for not understanding what I was getting. Im sure its a good product, just not what I wanted.
Love it but for price where is magnet sheet
These came as the v1.3 Wich are superior in that they are not going to shirt due to power surge, Wich is the reason behind buying them. Easy to install and overall great product
Big output improvement over stock and very high quality.
My X1 has been 100% stock because its just works so well. However, this upgrade solves all the things that made my X1 such a pain: different nozzles from all of my other printers, slower heating times, and the complete pain when changing nozzle diameters (the worst experience on these printers). Now all of my printers share the same Revo hotends, and I can swap on the fly!!
Flow rate is fantastic, and I got a 40% faster print with an obxidian 0.6mm than the equivalent hardened bambu nozzle with ABS-GF filament. I had to crank up the settings in orcaslicer, but I got the install and updates in less than 30 minutes, not including the calibration check.
I still have some oozing, given the improved flow, and the wires to the hotend could have been about 5mm longer, but these are nitpicks on what is probably the best upgrade I’ve had for any 3D printer!!!
Seems to work pretty well, however I think it would work best on a fesh, clean nozzle since I'm still getting some filament sticking to it. Overall it is good stuff.
This is really good stuff. I used some for my homeade bean dip the other day and was exactly the kind of spice I needed. 10/10
Great little board!
Note: This is a revised version (V2.4) ...bad number for revision! ...gets mixed up with Voron V2.4.
I replace my V1.0 because I inadvertantly plugged it in wrong and cooked it. This new board fit right in mechanically with no mods. Upon power, I love the red/blue led indicator. Makes it very easy to see when it is triggered. I did have an issue. It did not trigger Klipper. My old V1.O board did just fine but this new one did not. I could not find a schematic to see what actually changed. I was able to verify that the output line was changing. On my system from tap down at 0.0v to around 1.34v tap up. I was also able to verify that the pin (PB9) on my EBB36 was working fine as well. I found that changing my printer.cfg settings from EBBCan:PB9 to ^EBBCan:PB9 did the trick. Adding that circumflex, Klipper's trick to use a pull-up resistor on the STM32G0B1CBT6 chip of the EBB36 took care of my issue. It's working great now.
I really like these plates so far. ordering another for sure.
Awesome hotend. Works great and will be reliable for a long time. Rock solid construction
Purchased, took sometime to get the tracking moving. Website said 5-7 days mine took 16. This said its a high quality made to order CnC bed. Contacted CS and they where very very responsive. As of what i received, the bed is huge and super flat. Very happy with the purchase. Will buy again. This quality at this price is something special.
Fit it onto my V0 bed and the additional 20W over a standard 100W faster is FANTASTIC. Thank you West3D!
Exactly what you would hope for. I've put one inside the extrusions and another on the outside front.
Like many (most?) SV08 owners, my bed was a taco. I ordered this bed directly from Mandala as soon as it was available. It was easy to install, fit directly in place of the factory bed. I did have a little re-wiring to do as I replaced to tiny stock power supply and SSR, so I can't comment as far as how it worked with stock components. It has been a stellar upgrade. My bed map shows a range of 0.110 as measured using the BDSensor eddy probe.
Awesome product! Custom gifs for each state of the printer, and a constant display of job percentage.
Great kit with all the necessary hardware included. Pretty fun project so far
This boatd is great, plug and play no messing around! Pass through works flawless!
